Poland · PN
1.4539
PN EN 10088-5
Chemical composition
wt% · log scale- min – max range
- typical value
Mechanical properties
value range by conditionPhysical properties
vs. temperatureChemical composition
| Element | min | max | Similar | Remarks |
|---|---|---|---|---|
| C | 0.02 | |||
| Cr | 19 | 21 | ||
| Cu | 1.2 | 2 | ||
| Mn | 2 | |||
| Mo | 4 | 5 | ||
| N | 0.15 | |||
| Ni | 24 | 26 | ||
| P | 0.03 | |||
| S | 0.01 | For machinability %S=0 | ||
| Si | 0.7 |
Mechanical properties
| Heat treatment / condition | Yield strength | Tensile strength | Elongation | Reduction of area | Impact energy | Hardness |
|---|---|---|---|---|---|---|
| bright bars, Solution annealed, <= 10mm | ≥400 | 600–930 | ≥20 (Longitudinal) | |||
| bright bars, Solution annealed, > 10 <= 16mm | ≥400 | 600–930 | ≥20 (Longitudinal) | |||
| bright bars, Solution annealed, > 16 <= 40mm | ≥230 | 530–880 | ≥25 (Longitudinal) | ≥100 KV (long.) | ||
| bright bars, Solution annealed, > 160 <= 250mm | ≥230 | 530–730 | ≥30 (long.) | ≥60 KV (long.) | ||
| bright bars, Solution annealed, > 40 <= 63mm | ≥230 | 530–880 | ≥25 (Longitudinal) | ≥100 KV (long.) | ||
| bright bars, Solution annealed, > 63 <= 160mm | ≥230 | 530–730 | ≥35 (Longitudinal) | ≥100 KV (long.) | ||
| rods, bars, wire, sections, bright products +AT, <= 160mm | ≥230 | 530–730 | ≥35 Elongation after fracture (long.) | ≥100 KV (ISO-V) (trans.) | HB ≤230 | |
| rods, bars, wire, sections, bright products +AT, > 160 <= 250mm | ≥230 | 530–730 | ≥30 Elongation after fracture (long.) | ≥60 KV (ISO-V) (long.) | HB ≤230 |
Physical properties
20.0
| Elastic modulus | Mean thermal expansion | Thermal conductivity | Specific heat | Resistivity | Density | Poisson's ratio |
|---|---|---|---|---|---|---|
| 195.00;180.00;185.00 | 12.00 | 450.00 | 1.00 | 8.00 |
Typical physical values
| Density | Elastic modulus | Poisson's ratio | Remarks |
|---|---|---|---|
| 7.61–8.10 | 190.00–215.00 | 0.27–0.30 | Typical material properties for stainless steel. These values are not taken from the standard; they are indicative and must not be used for design. |
| 7.86 | 190.00–210.00 | 0.27–0.30 | Material properties for low-carbon, high-alloy steel. These values are not taken from the standard; they are indicative and must not be used for design. |
High/low temperature
| Condition | Temperature ℃ | max |
|---|---|---|
| heavy plates | sheets | 550 |
| heavy plates | sheets | 500 |
| heavy plates | sheets | 450 |
| heavy plates | sheets | 400 |
| heavy plates | sheets | 350 |
| heavy plates | sheets | 300 |
| heavy plates | sheets | 250 |
| heavy plates | sheets | 200 |
| heavy plates | sheets | 150 |
| heavy plates | sheets | 100 |
Similar grades
| Grade | Region | System |
|---|---|---|
| 1.4539 | UNI | |
| X 1 NiCrMoCu 25 20 5 | UNI | |
| 1.4539 | UNE | |
| X 1 NiCrMoCu 25 20 5 | UNE | |
| 1.4539 | STAS | |
| X 1 NiCrMoCu 25 20 5 | STAS | |
| 1.4539 | SS | |
| X 1 NiCrMoCu 25 20 5 | SS | |
| 1.4539 | SNV | |
| X 1 NiCrMoCu 25 20 5 | SNV | |
| 1.4539 | SFS | |
| X 1 NiCrMoCu 25 20 5 | SFS | |
| X 1 NiCrMoCu 25 20 5 | PN | |
| 1.4539 | ONORM | |
| X 1 NiCrMoCu 25 20 5 | ONORM | |
| 1.4539 | NS | |
| X 1 NiCrMoCu 25 20 5 | NS | |
| 1.4539 | NBN | |
| X 1 NiCrMoCu 25 20 5 | NBN | |
| 1.4539 | MSZ | |
| X 1 NiCrMoCu 25 20 5 | MSZ | |
| 1.4539 | Czech Republic | CSN |
| X 1 NiCrMoCu 25 20 5 | Czech Republic | CSN |
| 1.4539 | Bulgaria | BDS |
| X 1 NiCrMoCu 25 20 5 | Bulgaria | BDS |
| 1.4539 | B.S. | |
| X 1 NiCrMoCu 25 20 5 | B.S. | |
| 1.4539 | AFNOR NF | |
| X1NiCrMoCu25-20-5 | International standard | ISO |
| X 1 NiCrMoCu 25 20 5 | AFNOR NF | |
| X 1 NiCrMoCu 25 20 5 | DIN | |
| 1.4539 | DIN |