European Union · EN

EN AW-5049

EN 754-2:2013 — Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties; German version EN 754-2:2013

Chemical composition

wt% · log scale
0.010.1110Cr0.3Cu0.1Fe0.5Mg1.6 – 2.5Mn0.5 – 1.1Others each0.05Si0.4Ti0.1Total Others0.15Zn0.2
  • min – max range
  • typical value

Mechanical properties

value range by condition
Yield strength Rp0.2≥80 MPaTensile strength Rm180–250 MPaElongation A≥17 %HardnessHBDrawn tubes, Annealed +O, <= 20 mmYield strength Rp0.2≥100 MPaTensile strength Rm195–260 MPaElongation A≥13 %HardnessHBDrawn tubes, Strain-hardened - 1/8 hard +H11, <= 17 mmYield strength Rp0.2≥200 MPaTensile strength Rm260–310 MPaElongation A≥3 %HardnessHBDrawn tubes, Strain-hardened - 3/4 hard +H16, <= 5 mmYield strength Rp0.2≥140 MPaTensile strength Rm225–280 MPaElongation A≥7 %HardnessHBDrawn tubes, Strain-hardened - 3/8 hard +H13, <= 12 mm

Physical properties

vs. temperature
Elastic modulus GPa
70.0 – 70.0°C
Mean thermal expansion 10⁻⁶/K
23.5 – 23.7°C

Chemical composition

ElementminmaxSimilarRemarks
Al​​Bal​​
Cr0.3
Cu0.1
Fe0.5
Mg1.62.5
Mn0.51.1
Others each0.05Includes listed elements for which no specific limit is shown.
Si0.4
Ti0.1
Total Others0.15The sum of those "Others" metallic elements 0.010% or more each
Zn0.2

Mechanical properties

Heat treatment / conditionYield strengthTensile strengthElongationReduction of areaImpact energyHardness
Drawn tubes, Annealed +O, <= 20 mm≥80180–250≥17HB ≥50 HBW (typical value)
Drawn tubes, Strain-hardened - 1/8 hard +H11, <= 17 mm≥100195–260≥13HB ≥58 HBW (typical value)
Drawn tubes, Strain-hardened - 3/4 hard +H16, <= 5 mm≥200260–310≥3HB ≥83 HBW (typical value)
Drawn tubes, Strain-hardened - 3/8 hard +H13, <= 12 mm≥140225–280≥7HB ≥70 HBW (typical value)
Drawn tubes, Strain-hardened - 4/4 hard +H18, <= 3 mm≥240≥280≥2
Drawn tubes, Strain-hardened - 5/8 hard +H15, <= 7 mm≥180250–300≥3HB ≥80 HBW (typical value)
Drawn tubes, Strain-hardened - 7/8 hard +H17, <= 4 mm≥220270–320≥2HB ≥85 HBW (typical value)
Drawn tubes, Strain-hardened only +H111, <= 20 mm≥80180–250≥17HB ≥50 HBW (typical value)
Drawn tubes, strain hardened - 1/2 +H14, <= 10 mm≥160240–290≥4HB ≥75 HBW (typical value)
Drawn tubes, strain hardened - 1/4 +H12, <= 15 mm≥120210–270≥10HB ≥65 HBW (typical value)

Physical properties

20.0

Elastic modulusMean thermal expansionThermal conductivitySpecific heatResistivityDensityPoisson's ratio
70.0023.50138.00896.000.052.700.33

Typical physical values

DensityElastic modulusPoisson's ratioRemarks
2.60–2.9069.00–79.000.33Typical property values for aluminum alloys. These values are not taken from a published standard; they are indicative only and must not be used for design.

Similar grades

GradeRegionSystem
1050AUnited StatesAA
EN AW-AlMg2Mn08Italy
EN AW-5049ItalyUNI
EN AW-AlMg2Mn08Spain
EN AW-5049SpainUNE
EN AW-AlMg2Mn08Sweden
EN AW-5049SwedenSS
EN AW-AlMg2Mn08Switzerland
EN AW-5049SwitzerlandSNV
EN AW-AlMg2Mn08Finland
EN AW-5049FinlandSFS
EN AW-AlMg2Mn08Poland
EN AW-5049PolandPN
EN AW-AlMg2Mn08Austria
EN AW-5049AustriaONORM
EN AW-AlMg2Mn08Norway
EN AW-5049NorwayNS
EN AW-AlMg2Mn08Belgium
EN AW-5049BelgiumNBN
EN AW-AlMg2Mn08Hungary
EN AW-5049HungaryMSZ
EN AW-AlMg2Mn08Germany
EN AW-5049GermanyDIN
EN AW-AlMg2Mn08Czech Republic
EN AW-5049Czech RepublicCSN
EN AW-AlMg2Mn08United Kingdom
EN AW-5049United KingdomB.S.
EN AW-AlMg2Mn08Bulgaria
EN AW-5049BulgariaBDS
EN AW-AlMg2Mn08Romania
EN AW-5049RomaniaASRO
EN AW-AlMg2Mn08France
EN AW-5049FranceAFNOR NF
5049United StatesAA
3.3527GermanyDIN
AlMg2Mn08Germany